Are you from Mumbai?
Please Tell Us Your City
Knowing your city will help us provide relevant content to you.
Or Login with
Car insurance provides protection to the car's owner against third-party liabilities, theft or damage to the car.
Get the best Car Loan offers with lowest EMI quotes from our finance partner Bankbazaar.
Please tell us your city
Knowing your city helps us provide relevant content for you
Here is what i know and tested in my i20
1. Auto Door lock at 40kmph - You can activate this feature from the Authorized Service Center.
The central locking enables when you cross the speed of 40 kmph. Also in a scenario if you forgot to lock the car manually with the remote key after parking it - the doors gets locked with in 30 sec.
2. FATC (fully automatic Temperature Control) - Self diagnostic
If you have FATC (fully automatic Temperature Control) equipped in your i20 , you can run a self-diagnostic to make sure the components related to it working properly.
To get into the self diagnosis mode1. Put the key into the ignition hole2. Turn the key into ON position so the dashboard lights illuminates (No starting of engine)3. Press and hold the OFF button, then press the MODE button more than 4 times within 2seconds4. The you can see the Display unit of a/c illuminates like in the video and display codes starts blinking.5. Now the diagnosis starts6. press the A/C button to proceed to next step7. after completion it will come into the original condition8. Incase if you wants to quit anytime press OFF button
Here are the other codes which will display if any of the component related to F.A.T.C malfunctions.00 = Normal11 = In-car temparature sensor open12 = In-car temparature sensor short13 = Ambient temparature sensor open14 = Ambient temparature sensor short17 = Evaporator temparature sensor open18 = Evaporator temparature sensor short19 = Temparature control actuator feed back open20 = Temparature control actuatore failure 21 = Mode Control actuator open21 = Mode control actuator short22 = Mode control actuator failure25 = Intake potentiometer open25 = Intake potentiometer short26 = Intake potentiometer failure
3. Firmware version check for HU (Head Unit/ Stereo)
Here are the button combination for displaying this text ( Press one by one but immediately)
Press and Hold 1FF, the 6
if the version shows in MID is VER M58 S71 D29 or higher then you HU is a good one
if the version shows in MID is VER M08 S69 D18 ( important to look for S69) then your HU have some issues like
1. HU automatically switches OFF while running2. HU fuse pops up when you press Eject button while ignition is at OFF position.
You can get a free replacement of HU from Hyundai if you found your version as S69
PS:- If any one knows more about i20 Tips & Tricks please do share the same here.
Rheostat Ilumination Control
Fitted a Rheostat Ilumination Control (Part No: 94950-1J0009P) to control the illumination brightness inside cabin. here are the pics and Video. This helps in night driving.Cost: Rs.579/-
Watch this Video
DO you know some hyndai service center where it is available.?
You can ask in Any Hyundai A.S.S, if its not readily available you can order and it will be with them in couple of days. Cost of the equipment is some where around 450/- and rest is service charges.
Firmware version check for HU (Head Unit/ Stereo)
when i press and hold 1ff and then 6 nothing happended. what exactly is the process
Wildon, I need your help to decode the VIN/ chassis number. Can you please PM, as I cannot send you PM. Or do I need to paste the given VIN here?
Enable RDS in Indian i20
I was able to change my HU region to Europe, so the RDS feature was enabled. It's nice to see your Local FM station name too in the Display.But i was not able to reproduce the combination until today for the benefit of others .. 1. Press and hold 1FF and then immediately press 4, release both the fingers ,then press 1FF Four times as fast as you can.2. Now you can see the display in MID as VER M58 S71 D29, immediately press button 6 so you can see your present region as General in MID.3. Rotate the File/Enter/Tune knobe to change the region to Europe and Press/Push the Knob, now you can see the display as area changed.4. Switch ON the HU by Press/push the Power Button and press the SETUP button, Rotate the File/Enter/Tune knobe and enable the features you want and press/push the knob to store the settings.I'll be adding a video soon.Note: when you press only 1FF and 6 it shows a different Version display likeVER M08 S71 D29, in which you cannot enter the setup.There are other parameters can be changed after you enter the setup, but its not worth it, so i'm not mentioning here.
THAKS WHEN I CHECKED MY MID SHOWS VER M26 S17D67 AND WHEN I PRESS T6 IT SHOWS DSP:PB26KG,IND AND NOTHING HAPPENS AFTER THAT NO KEY OR SCRCOLLING MAKE ANY DIFF. I M SAD
You almost got near to it.
When you MID shows VER M26 S17D67 then press 6 so MID will show " Select area" then rotate the nob for selecting Europe and press the knob to store the setting.
There is an error in my post #7
please read the 1st point as below
1. Press and hold 1FF and then immediately press 4, release both the fingers ,then press 1FF Four times as fast as you can.
MODS:- If possible please edit the post #7